#Hydros control 2 full#
Hydros is coming out with a full line of flow sensors in the future that can be used on any sense port. Both can be used on any sense port.ġ/4" flow sensor to measure RODI production rate. PH sensor Hydros Control 4 has 2 probe ports that can be used for ORP or PH.Ģ leak detection sensors 1 below the overflow box and one below the bulkheads on the sump Hydros has 2 types of leak sensors, a rope sensor and a non-contact puck sensor. Hydros has dual sensor optical sensors that can be used on any sense port. These can be used on any sense port on the Control 4/2 or XSġ optical sensor to tell me if the sump level gets too high. Hydros has 2 types of digital temperature sense probes that can be used for controlling outlets and sending alerts. Hydros has 2 types of digital temperature sense probes that can be used for controlling outlets and sending alerts.ĭual temp sensors 1 in the sump 1 in the tank over flow box. Turns my fuge light on and off based on time. Hydros has 2 types of digital temperature sense probes that can be used for controlling outlets and sending alerts.ġ 300watt main heater that turns on and off based on temp See above for controlled outlets. Hydros has a single outlet wifi outlet that supports upto 10Aġ 500watt backup heater that turns on and off based on temp (only runs if for some reason the 300w cant keep up) See above for controlled outlets.
Coming in the future will also be WIRED outlet bars that can give you even more outputs.ġ EB4 that turns my chiller on and off based on temp (it draws 7.5amp). That would give you up to 32 wifi controlled outlets. Hydros has 4 outlet wifi controlled outlet bars, you can have up to 8 wifi devices per hydros or hydros collective. It's going to be pretty neat when finished.Īs for current and near future capabilities of hydros, here is what I can tell you:Ģ EB832's with 14 things plugged in from lights, wave engine, pumps, AutoAqua AWC, etc. You'll be able to share modes across controllers, use inputs from a Control 2/4/XS to trigger pump/wavemaker actions, and more.
#Hydros control 2 update#
Plus it monitor there power consumption.Ĭlick to expand.Currently wave engine is stand alone but they are working on a firmware and app update that brings it fully integrated into the hydros control platform when used in a hydros collective. I do not use the apex to control the Display lights or pumps it is simple used to turn those on or off if needed. I also have a Tunze Stream3 that I wish I could control with the Hydro. Turns my fuge light on and off based on time.ĭual temp sensors 1 in the sump 1 in the tank over flow box.ġ optical sensor to tell me if the sump level gets too high.Ģ leak detection sensors 1 below the overflow box and one below the bulkheads on the sumpġ/4" flow sensor to measure RODI production rate.ĭOS for ALK and CAL dosing controlled by the Trident.
I already run a Wave engine that controls my 4 XF350 Gyre's and I like it.ĭoes the Wave Engine integrate with the Hydro's controller or does it remain separate?Ģ EB832's with 14 things plugged in from lights, wave engine, pumps, AutoAqua AWC, etc.ġ EB4 that turns my chiller on and off based on temp (it draws 7.5amp)ġ 500watt backup heater that turns on and off based on temp (only runs if for some reason the 300w cant keep up)ġ 300watt main heater that turns on and off based on tempĩ0 watt UV that is always on unless something happens and temp goes crazy then Apex would shut if off. I'm not currently looking to switch from Apex but I will say what I have and see if Hydros can do the same.
0 kommentar(er)
